1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
|
#ifndef HWDEF_EMISAR_D1SV2_H
#define HWDEF_EMISAR_D1SV2_H
/* Emisar D1Sv2 driver layout (attiny1634)
*
* Pin / Name / Function
* 1 PA6 red aux LED (PWM1B)
* 2 PA5 green aux LED (PWM0B)
* 3 PA4 blue aux LED
* 4 PA3 battery voltage (ADC0)
* 5 PA2 (none)
* 6 PA1 (none)
* 7 PA0 (none)
* 8 GND GND
* 9 VCC VCC
* 10 PC5 (none)
* 11 PC4 (none)
* 12 PC3 RESET
* 13 PC2 (none)
* 14 PC1 SCK
* 15 PC0 (none) PWM0A
* 16 PB3 main LED PWM (PWM1A)
* 17 PB2 MISO
* 18 PB1 MOSI
* 19 PB0 Opamp power
* 20 PA7 e-switch (PCINT7)
* ADC12 thermal sensor
*
* Main LED power uses one pin to turn the Opamp on/off,
* and one pin to control Opamp power level.
* All brightness control uses the power level pin, with 4 kHz 10-bit PWM.
* The on/off pin is only used to turn the main LED on and off,
* not to change brightness.
*/
#ifdef ATTINY
#undef ATTINY
#endif
#define ATTINY 1634
#include <avr/io.h>
#define PWM_CHANNELS 1
#define PWM_BITS 10 // 0 to 1023 at 4 kHz, not 0 to 255 at 16 kHz
#define SWITCH_PIN PA7 // pin 20
#define SWITCH_PCINT PCINT7 // pin 20 pin change interrupt
#define SWITCH_PCIE PCIE0 // PCIE0 is for PCINT[7:0]
#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
#define SWITCH_PORT PINA // PINA or PINB or PINC
#define PWM1_PIN PB3 // pin 16, Opamp reference
#define PWM1_LVL OCR1A // OCR1A is the output compare register for PB3
#define LED_ENABLE_PIN PB0 // pin 19, Opamp power
#define LED_ENABLE_PORT PORTB // control port for PB0
//#define PWM2_PIN PB0 // pin 19, Opamp power
// FIXME:
//#define PWM2_LVL OCR1B // OCR1B is the output compare register for PB1
#define ADC_PRSCL 0x06 // clk/64
// average drop across diode on this hardware
#ifndef VOLTAGE_FUDGE_FACTOR
#define VOLTAGE_FUDGE_FACTOR 4 // add 0.20V (measured 0.22V)
#endif
#define TEMP_CHANNEL 0b00001111
// this light has aux LEDs under the optic
#define AUXLED_R_PIN PA6 // pin 1
#define AUXLED_G_PIN PA5 // pin 2
#define AUXLED_B_PIN PA4 // pin 3
#define AUXLED_RGB_PORT PORTA // PORTA or PORTB or PORTC
#define AUXLED_RGB_DDR DDRA // DDRA or DDRB or DDRC
#define AUXLED_RGB_PUE PUEA // PUEA or PUEB or PUEC
// with so many pins, doing this all with #ifdefs gets awkward...
// ... so just hardcode it in each hwdef file instead
inline void hwdef_setup() {
// enable output ports
// Opamp level and Opamp on/off
DDRB = (1 << PWM1_PIN)
| (1 << LED_ENABLE_PIN);
// aux R/G/B
DDRA = (1 << AUXLED_R_PIN)
| (1 << AUXLED_G_PIN)
| (1 << AUXLED_B_PIN)
;
// configure PWM
// Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
// pre-scale for timer: N = 1
// WGM1[3:0]: 0,0,1,1: PWM, Phase Correct, 10-bit (DS table 12-5)
// CS1[2:0]: 0,0,1: clk/1 (No prescaling) (DS table 12-6)
// COM1A[1:0]: 1,0: PWM OC1A in the normal direction (DS table 12-4)
// COM1B[1:0]: 0,0: PWM OC1B disabled (DS table 12-4)
TCCR1A = (1<<WGM11) | (1<<WGM10) // 10-bit (TOP=0x03FF) (DS table 12-5)
| (1<<COM1A1) | (0<<COM1A0) // PWM 1A in normal direction (DS table 12-4)
| (0<<COM1B1) | (0<<COM1B0) // PWM 1B in normal direction (DS table 12-4)
;
TCCR1B = (0<<CS12) | (0<<CS11) | (1<<CS10) // clk/1 (no prescaling) (DS table 12-6)
| (0<<WGM13) | (0<<WGM12) // phase-correct PWM (DS table 12-5)
;
// set up e-switch
//PORTA = (1 << SWITCH_PIN); // TODO: configure PORTA / PORTB / PORTC?
PUEA = (1 << SWITCH_PIN); // pull-up for e-switch
SWITCH_PCMSK = (1 << SWITCH_PCINT); // enable pin change interrupt
}
#define LAYOUT_DEFINED
#endif
|
