1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
#ifndef HWDEF_SOFIRN_SP10S_H
#define HWDEF_SOFIRN_SP10S_H
// TODO: rename to sofirn-sp10s-gchart?
/* gChart's PIC12 to ATTINY1616 v1 adapter for the SP10S
https://oshpark.com/shared_projects/b4IZEGSy
PIC12 Pinout:
1 - VDD
2 - No Connect
3 - Low Channel FET (series 4.7K Ohms)
4 - Switch
5 - High Channel FET (main PWM)
6 - Voltage Divider (300K:100K Ohms)
7 - Boost chip enable
8 - GND
ATTINY1616 Mapping:
2 - PA5 : (no connect)
3 - PB5 : TCA0 - WO2 Alternate MUX
4 - PB3 : (switch)
5 - PB0 : TCA0 - WO0
6 - PB4 : ADC0 - AIN9
7 - PA1 : (boost enable)
*/
#define LAYOUT_DEFINED
#ifdef ATTINY
#undef ATTINY
#endif
#define ATTINY 1616
#include <avr/io.h>
#ifndef SWITCH_PIN
#define SWITCH_PIN 3
#define SWITCH_PORT VPORTB.IN
#define SWITCH_ISC_REG PORTB.PIN3CTRL
#define SWITCH_VECT PORTB_PORT_vect
#define SWITCH_INTFLG VPORTB.INTFLAGS
#endif
#define PWM_CHANNELS 2
// Small channel
#ifndef PWM1_PIN
#define PWM1_PIN PB5
#define PWM1_LVL TCA0.SINGLE.CMP2 // PB5 is Alternate MUX for TCA Compare 2
#endif
// Big channel
#ifndef PWM2_PIN
#define PWM2_PIN PB0
#define PWM2_LVL TCA0.SINGLE.CMP0 // PB0 is TCA Compare 0
#endif
#define LED_ENABLE_PIN PIN1_bp
#define LED_ENABLE_PORT PORTA_OUT
#define USE_VOLTAGE_DIVIDER // use a dedicated pin, not VCC, because VCC input is flattened
#define DUAL_VOLTAGE_FLOOR 20 // for AA/14500 boost drivers, don't indicate low voltage if below this level
#define DUAL_VOLTAGE_LOW_LOW 07 // the lower voltage range's danger zone 0.7 volts
#define ADMUX_VOLTAGE_DIVIDER ADC_MUXPOS_AIN9_gc // which ADC channel to read
// Raw ADC readings at 4.4V and 2.2V
// calibrate the voltage readout here
// estimated / calculated values are:
// (voltage - D1) * (R2/(R2+R1) * 1024 / 1.1)
// Resistors are 300,000 and 100,000
#ifndef ADC_44
#define ADC_44 1023 // raw value at 4.40V
#endif
#ifndef ADC_22
#define ADC_22 512 // raw value at 2.20V
#endif
// with so many pins, doing this all with #ifdefs gets awkward...
// ... so just hardcode it in each hwdef file instead
inline void hwdef_setup() {
// set up the system clock to run at 10 MHz instead of the default 3.33 MHz
_PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
VPORTA.DIR = PIN1_bm; // Boost enable pin
VPORTB.DIR = PIN0_bm | PIN5_bm; // PWM pins as output
//VPORTC.DIR = ...;
// enable pullups on the input pins to reduce power
PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
//PORTA.PIN1CTRL = PORT_PULLUPEN_bm; // Boost enable pin
PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
PORTA.PIN5CTRL = PORT_PULLUPEN_bm;
PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // Big PWM channel
PORTB.PIN1CTRL = PORT_PULLUPEN_bm;
PORTB.PIN2CTRL = PORT_PULLUPEN_bm;
PORTB.PIN3CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc; // Switch
//PORTB.PIN4CTRL = PORT_PULLUPEN_bm; // Voltage divider
//PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Small PWM channel
//PORTC.PIN0CTRL = PORT_PULLUPEN_bm; connected to the ADC via airwire
PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
// set up the PWM
// https://ww1.microchip.com/downloads/en/DeviceDoc/ATtiny1614-16-17-DataSheet-DS40002204A.pdf
// PB0 is TCA0:WO0, use TCA_SINGLE_CMP0EN_bm
// PB1 is TCA0:WO1, use TCA_SINGLE_CMP1EN_bm
// PB2 is TCA0:WO2, use TCA_SINGLE_CMP2EN_bm
// For Fast (Single Slope) PWM use TCA_SINGLE_WGMODE_SINGLESLOPE_gc
// For Phase Correct (Dual Slope) PWM use TCA_SINGLE_WGMODE_DSBOTTOM_gc
// See the manual for other pins, clocks, configs, portmux, etc
PORTMUX.CTRLC = PORTMUX_TCA02_ALTERNATE_gc; // Use alternate pin for TCA0:WO2
TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP2EN_bm | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
TCA0.SINGLE.PER = 255;
TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
}
#endif
|
