1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
|
// Emisar D1S v2 config options for Anduril
#include "hwdef-Emisar_D1Sv2.h"
// ATTINY: 1634
// this light has three aux LED channels: R, G, B
#define USE_AUX_RGB_LEDS
#define USE_AUX_RGB_LEDS_WHILE_ON
#define USE_INDICATOR_LED_WHILE_RAMPING
#define RGB_LED_OFF_DEFAULT 0x18 // low, voltage
#define RGB_LED_LOCKOUT_DEFAULT 0x37 // blinking, rainbow
// enable blinking aux LEDs
#define TICK_DURING_STANDBY
#define STANDBY_TICK_SPEED 3 // every 0.128 s
// ../../bin/level_calc.py cube 1 150 7135 1 4 1300
// (with max_pwm set to 1023)
#define RAMP_LENGTH 150
#define PWM1_LEVELS 1,1,2,2,3,3,4,4,5,6,6,7,8,9,10,11,12,13,14,15,16,17,18,20,21,23,24,26,27,29,31,32,34,36,38,40,43,45,47,49,52,54,57,60,62,65,68,71,74,77,81,84,87,91,95,98,102,106,110,114,118,122,127,131,136,141,145,150,155,160,166,171,176,182,188,193,199,205,211,218,224,231,237,244,251,258,265,272,280,287,295,303,310,319,327,335,344,352,361,370,379,388,397,407,416,426,436,446,457,467,477,488,499,510,521,533,544,556,568,580,592,604,617,629,642,655,668,682,695,709,723,737,751,766,781,795,810,826,841,857,872,888,904,921,937,954,971,988,1005,1023
#define MAX_1x7135 50
// the entire ramp is regulated; don't blink halfway up
#ifdef BLINK_AT_RAMP_MIDDLE
#undef BLINK_AT_RAMP_MIDDLE
#endif
// don't slow down at low levels; this isn't that sort of light
// (it needs to stay at full speed for the 10-bit PWM to work)
#ifdef USE_DYNAMIC_UNDERCLOCKING
#undef USE_DYNAMIC_UNDERCLOCKING
#endif
#define RAMP_SMOOTH_FLOOR 1
#define RAMP_SMOOTH_CEIL 130
// 10, 30, [50], 70, 90, 110, 130
#define RAMP_DISCRETE_FLOOR 10
#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL
#define RAMP_DISCRETE_STEPS 7
#define MUGGLE_FLOOR RAMP_DISCRETE_FLOOR
#define MUGGLE_CEILING 70
// optional, makes initial turbo step-down faster so first peak isn't as hot
// the D4 runs very very hot, so be extra careful
//#define THERM_HARD_TURBO_DROP
// stop panicking at ~70% power or ~900 lm
#define THERM_FASTER_LEVEL 130
// respond to thermal changes faster
#define THERMAL_WARNING_SECONDS 3
#define THERMAL_UPDATE_SPEED 1
#define THERM_PREDICTION_STRENGTH 4
// easier access to thermal config mode, for Emisar
#define USE_TENCLICK_THERMAL_CONFIG
// slow down party strobe; this driver can't pulse for 1ms or less
#define PARTY_STROBE_ONTIME 2
#define THERM_CAL_OFFSET 5
// attiny1634 has enough space to smooth out voltage readings
// (prevent the button from blinking during use)
#define USE_VOLTAGE_LOWPASS
|
