1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
|
// Noctigon K1 12V config options for Anduril
#define MODEL_NUMBER "0253"
#include "hwdef-Noctigon_K1-12V.h"
// ATTINY: 1634
// Most K1 lights can run hotter than default, but the 12V model
// is known to have issues with the driver itself getting too hot.
// This then causes the main LEDs to turn off during use, because the
// boost chip's built-in protection activates. So try to keep the
// temperature relatively low.
#undef DEFAULT_THERM_CEIL
#define DEFAULT_THERM_CEIL 45
// this light has three aux LED channels: R, G, B
#define USE_AUX_RGB_LEDS
#define USE_AUX_RGB_LEDS_WHILE_ON
#define USE_INDICATOR_LED_WHILE_RAMPING
// enable blinking aux LEDs
#define TICK_DURING_STANDBY
#define STANDBY_TICK_SPEED 3 // every 0.128 s
// level_calc.py cube 1 150 7135 0 4 1300
// (with max_pwm set to 1023)
// (level 0 is usable on this light)
#define RAMP_LENGTH 150
#define PWM1_LEVELS 0,0,1,1,2,2,3,3,4,5,5,6,7,8,9,10,11,12,13,14,15,16,17,19,20,22,23,25,26,28,30,31,33,35,37,39,42,44,46,48,51,53,56,59,61,64,67,70,73,76,80,83,86,90,94,97,101,105,109,113,117,122,126,130,135,140,144,149,154,159,165,170,175,181,187,193,198,204,211,217,223,230,236,243,250,257,264,271,279,286,294,302,310,318,326,334,343,351,360,369,378,387,397,406,416,426,436,446,456,466,477,488,499,510,521,532,544,555,567,579,591,604,616,629,642,655,668,682,695,709,723,737,751,766,780,795,810,825,841,856,872,888,904,921,937,954,971,988,1005,1023
#define MAX_1x7135 50
// the entire ramp is regulated; don't blink halfway up
#ifdef BLINK_AT_RAMP_MIDDLE
#undef BLINK_AT_RAMP_MIDDLE
#endif
// don't slow down at low levels; this isn't that sort of light
// (it needs to stay at full speed for the 10-bit PWM to work)
#ifdef USE_DYNAMIC_UNDERCLOCKING
#undef USE_DYNAMIC_UNDERCLOCKING
#endif
#define RAMP_SMOOTH_FLOOR 1
#define RAMP_SMOOTH_CEIL 130
// 10, 30, [50], 70, 90, 110, 130
#define RAMP_DISCRETE_FLOOR 10
#define RAMP_DISCRETE_CEIL RAMP_SMOOTH_CEIL
#define RAMP_DISCRETE_STEPS 7
// safe limit ~50% power
#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR
#define SIMPLE_UI_CEIL 120
#define SIMPLE_UI_STEPS 5
// make candle mode wobble more
#define CANDLE_AMPLITUDE 32
// stop panicking at ~70% power or ~600 lm
#define THERM_FASTER_LEVEL 130
#define THERM_RESPONSE_MAGNITUDE 32 // smaller adjustments, this host changes temperature slowly
#define THERM_NEXT_WARNING_THRESHOLD 32 // more error tolerance before adjusting
// slow down party strobe; this driver can't pulse for 1ms or less
#define PARTY_STROBE_ONTIME 4
#define THERM_CAL_OFFSET 5
|
