blob: d5264552de03fd53a8dd3cf6d0a00f88263afcfc (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
|
/*
* fsm-main.c: main() function for SpaghettiMonster.
*
* Copyright (C) 2017 Selene ToyKeeper
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
#ifndef FSM_MAIN_C
#define FSM_MAIN_C
#include "fsm-main.h"
#if PWM_CHANNELS == 4
// 4th PWM channel requires manually turning the pin on/off via interrupt :(
ISR(TIMER1_OVF_vect) {
//bitClear(PORTB, 3);
PORTB &= 0b11110111;
//PORTB |= 0b00001000;
}
ISR(TIMER1_COMPA_vect) {
//if (!bitRead(TIFR,TOV1)) bitSet(PORTB, 3);
if (! (TIFR & (1<<TOV1))) PORTB |= 0b00001000;
//if (! (TIFR & (1<<TOV1))) PORTB &= 0b11110111;
}
#endif
int main() {
// Don't allow interrupts while booting
cli();
//WDT_off();
//PCINT_off();
// configure PWM channels
#if PWM_CHANNELS >= 1
DDRB |= (1 << PWM1_PIN);
TCCR0B = 0x01; // pre-scaler for timer (1 => 1, 2 => 8, 3 => 64...)
TCCR0A = PHASE;
#endif
#if PWM_CHANNELS >= 2
DDRB |= (1 << PWM2_PIN);
#endif
#if PWM_CHANNELS >= 3
// Second PWM counter is ... weird
DDRB |= (1 << PWM3_PIN);
TCCR1 = _BV (CS10);
GTCCR = _BV (COM1B1) | _BV (PWM1B);
OCR1C = 255; // Set ceiling value to maximum
#endif
#if PWM_CHANNELS >= 4
// 4th PWM channel is ... not actually supported in hardware :(
DDRB |= (1 << PWM4_PIN);
//OCR1C = 255; // Set ceiling value to maximum
TCCR1 = 1<<CTC1 | 1<<PWM1A | 3<<COM1A0 | 2<<CS10;
GTCCR = (2<<COM1B0) | (1<<PWM1B);
// set up an interrupt to control PWM4 pin
TIMSK |= (1<<OCIE1A) | (1<<TOIE1);
#endif
// configure e-switch
PORTB = (1 << SWITCH_PIN); // e-switch is the only input
PCMSK = (1 << SWITCH_PIN); // pin change interrupt uses this pin
// configure sleep mode
set_sleep_mode(SLEEP_MODE_PWR_DOWN);
// Read config values and saved state
// TODO: handle long press vs short press (or even medium press)?
#ifdef USE_DEBUG_BLINK
//debug_blink(1);
#endif
// all booted -- turn interrupts back on
PCINT_on();
WDT_on();
ADC_on();
sei();
// in case any spurious button presses were detected at boot
#ifdef USE_DELAY_MS
delay_ms(1);
#else
delay_4ms(1);
#endif
empty_event_sequence();
// fallback for handling a few things
#ifndef DONT_USE_DEFAULT_STATE
push_state(default_state, 0);
#endif
// call recipe's setup
setup();
// main loop
while (1) {
// if event queue not empty, empty it
process_emissions();
// enter standby mode if requested
// (works better if deferred like this)
if (go_to_standby) {
go_to_standby = 0;
#ifdef USE_RAMPING
set_level(0);
#else
#if PWM_CHANNELS >= 1
PWM1_LVL = 0;
#endif
#if PWM_CHANNELS >= 2
PWM2_LVL = 0;
#endif
#if PWM_CHANNELS >= 3
PWM3_LVL = 0;
#endif
#if PWM_CHANNELS >= 4
PWM4_LVL = 255; // inverted :(
#endif
#endif
standby_mode();
}
// give the recipe some time slices
loop();
}
}
#endif
|
