reorganized project files (part 1)

(just moved files, didn't change the contents yet,
 and nothing will work without updating #includes and build scripts and stuff)

1 files changed, 0 insertions, 171 deletions

diff --git a/hwdef-emisar-d4v2.h b/hwdef-emisar-d4v2.h
deleted file mode 100644
index 96c57a9..0000000
--- a/hwdef-emisar-d4v2.h
+++ /dev/null
@@ -1,171 +0,0 @@
-// hwdef for Emisar D4v2 (attiny1634)
-// Copyright (C) 2018-2023 Selene ToyKeeper
-// SPDX-License-Identifier: GPL-3.0-or-later
-#pragma once
-
-/*
- * Pin / Name / Function
- *   1    PA6   FET PWM (direct drive) (PWM1B)
- *   2    PA5   R: red aux LED (PWM0B)
- *   3    PA4   G: green aux LED
- *   4    PA3   B: blue aux LED
- *   5    PA2   e-switch
- *   6    PA1   button LED
- *   7    PA0   (none)
- *   8    GND   GND
- *   9    VCC   VCC
- *  10    PC5   (none)
- *  11    PC4   (none)
- *  12    PC3   RESET
- *  13    PC2   (none)
- *  14    PC1   SCK
- *  15    PC0   (none) PWM0A
- *  16    PB3   7135 PWM (PWM1A)
- *  17    PB2   MISO
- *  18    PB1   MOSI
- *  19    PB0   (none)
- *  20    PA7   (none)
- *      ADC12   thermal sensor
- */
-
-#define ATTINY 1634
-#include <avr/io.h>
-
-#ifndef HWDEF_C_FILE
-#define HWDEF_C_FILE hwdef-emisar-d4v2.c
-#endif
-
-// allow using aux LEDs as extra channel modes
-#include "chan-rgbaux.h"
-
-// channel modes:
-// * 0. FET+7135 stacked
-// * 1+. aux RGB
-#define NUM_CHANNEL_MODES   (1 + NUM_RGB_AUX_CHANNEL_MODES)
-enum CHANNEL_MODES {
-    CM_MAIN = 0,
-    RGB_AUX_ENUMS
-};
-
-#define DEFAULT_CHANNEL_MODE  CM_MAIN
-
-// right-most bit first, modes are in fedcba9876543210 order
-#define CHANNEL_MODES_ENABLED 0b0000000000000001
-// no args
-//#define USE_CHANNEL_MODE_ARGS
-//#define CHANNEL_MODE_ARGS     0,0,0,0,0,0,0,0
-
-
-#define PWM_CHANNELS 2  // old, remove this
-
-#define PWM_BITS      16        // dynamic 16-bit, but never goes over 255
-#define PWM_GET       PWM_GET8
-#define PWM_DATATYPE  uint16_t  // is used for PWM_TOPS (which goes way over 255)
-#define PWM_DATATYPE2 uint16_t  // only needs 32-bit if ramp values go over 255
-#define PWM1_DATATYPE uint8_t   // 1x7135 ramp
-#define PWM2_DATATYPE uint8_t   // DD FET ramp
-
-// PWM parameters of both channels are tied together because they share a counter
-#define PWM_TOP       ICR1   // holds the TOP value for for variable-resolution PWM
-#define PWM_TOP_INIT  255    // highest value used in top half of ramp
-#define PWM_CNT       TCNT1  // for dynamic PWM, reset phase
-
-// 1x7135 channel
-#define CH1_PIN  PB3            // pin 16, 1x7135 PWM
-#define CH1_PWM  OCR1A          // OCR1A is the output compare register for PB3
-
-// DD FET channel
-#define CH2_PIN  PA6            // pin 1, DD FET PWM
-#define CH2_PWM  OCR1B          // OCR1B is the output compare register for PA6
-
-// e-switch
-#define SWITCH_PIN   PA2    // pin 5
-#define SWITCH_PCINT PCINT2 // pin 5 pin change interrupt
-#define SWITCH_PCIE  PCIE0  // PCIE0 is for PCINT[7:0]
-#define SWITCH_PCMSK PCMSK0 // PCMSK0 is for PCINT[7:0]
-#define SWITCH_PORT  PINA   // PINA or PINB or PINC
-#define SWITCH_PUE   PUEA   // pullup group A
-#define PCINT_vect   PCINT0_vect  // ISR for PCINT[7:0]
-
-
-#define ADC_PRSCL   0x07    // clk/128
-
-// average drop across diode on this hardware
-#ifndef VOLTAGE_FUDGE_FACTOR
-#define VOLTAGE_FUDGE_FACTOR 4  // add 0.20V  (measured 0.22V)
-#endif
-
-// this light has aux LEDs under the optic
-#define AUXLED_R_PIN    PA5    // pin 2
-#define AUXLED_G_PIN    PA4    // pin 3
-#define AUXLED_B_PIN    PA3    // pin 4
-#define AUXLED_RGB_PORT PORTA  // PORTA or PORTB or PORTC
-#define AUXLED_RGB_DDR  DDRA   // DDRA or DDRB or DDRC
-#define AUXLED_RGB_PUE  PUEA   // PUEA or PUEB or PUEC
-
-#define BUTTON_LED_PIN  PA1    // pin 6
-#define BUTTON_LED_PORT PORTA  // for all "PA" pins
-#define BUTTON_LED_DDR  DDRA   // for all "PA" pins
-#define BUTTON_LED_PUE  PUEA   // for all "PA" pins
-
-// this light has three aux LED channels: R, G, B
-#define USE_AUX_RGB_LEDS
-// it also has an independent LED in the button
-#define USE_BUTTON_LED
-// the aux LEDs are front-facing, so turn them off while main LEDs are on
-#ifdef USE_INDICATOR_LED_WHILE_RAMPING
-#undef USE_INDICATOR_LED_WHILE_RAMPING
-#endif
-
-
-inline void hwdef_setup() {
-    // enable output ports
-    // 7135
-    DDRB = (1 << CH1_PIN);
-    // DD FET, aux R/G/B, button LED
-    DDRA = (1 << CH2_PIN)
-         | (1 << AUXLED_R_PIN)
-         | (1 << AUXLED_G_PIN)
-         | (1 << AUXLED_B_PIN)
-         | (1 << BUTTON_LED_PIN)
-         ;
-
-    // configure PWM
-    // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
-    // pre-scale for timer: N = 1
-    // WGM1[3:0]: 1,0,1,0: PWM, Phase Correct, adjustable (DS table 12-5)
-    // CS1[2:0]:    0,0,1: clk/1 (No prescaling) (DS table 12-6)
-    // COM1A[1:0]:    1,0: PWM OC1A in the normal direction (DS table 12-4)
-    // COM1B[1:0]:    1,0: PWM OC1B in the normal direction (DS table 12-4)
-    TCCR1A  = (1<<WGM11)  | (0<<WGM10)   // adjustable PWM (TOP=ICR1) (DS table 12-5)
-            | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
-            | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)
-            ;
-    TCCR1B  = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
-            | (1<<WGM13)  | (0<<WGM12)  // phase-correct adjustable PWM (DS table 12-5)
-            ;
-
-    // set PWM resolution
-    PWM_TOP = PWM_TOP_INIT;
-
-    #if 0  // old 8-bit PWM setup
-    // configure PWM
-    // Setup PWM. F_pwm = F_clkio / 2 / N / TOP, where N = prescale factor, TOP = top of counter
-    // pre-scale for timer: N = 1
-    TCCR1A  = (0<<WGM11)  | (1<<WGM10)   // 8-bit (TOP=0xFF) (DS table 12-5)
-            | (1<<COM1A1) | (0<<COM1A0)  // PWM 1A in normal direction (DS table 12-4)
-            | (1<<COM1B1) | (0<<COM1B0)  // PWM 1B in normal direction (DS table 12-4)
-            ;
-    TCCR1B  = (0<<CS12)   | (0<<CS11) | (1<<CS10)  // clk/1 (no prescaling) (DS table 12-6)
-            | (0<<WGM13)  | (0<<WGM12)  // phase-correct PWM (DS table 12-5)
-            ;
-    #endif
-
-    // set up e-switch
-    SWITCH_PUE = (1 << SWITCH_PIN);  // pull-up for e-switch
-    SWITCH_PCMSK = (1 << SWITCH_PCINT);  // enable pin change interrupt
-}
-
-
-#define LAYOUT_DEFINED
-