added early initial attempt at a boost/12V/6V version of the MD11

(had to guess about some hardware details, unsure if correct)

1 files changed, 70 insertions, 0 deletions

diff --git a/spaghetti-monster/anduril/cfg-noctigon-md11-12v.h b/spaghetti-monster/anduril/cfg-noctigon-md11-12v.h
new file mode 100644
index 0000000..1c90ab1
--- /dev/null
+++ b/spaghetti-monster/anduril/cfg-noctigon-md11-12v.h
@@ -0,0 +1,70 @@
+// Noctigon MD11 (12V) config options for Anduril
+#define MODEL_NUMBER "0273"
+#include "hwdef-Noctigon_MD11-12V.h"
+#include "hank-cfg.h"
+// ATTINY: 1634
+
+// this light has three aux LED channels: R, G, B
+#define USE_AUX_RGB_LEDS
+// ... and a single LED in the button
+#define USE_BUTTON_LED
+// don't use aux LEDs while main LED is on
+#ifdef USE_INDICATOR_LED_WHILE_RAMPING
+#undef USE_INDICATOR_LED_WHILE_RAMPING
+#endif
+
+
+// power channels:
+// - linear: 5A?
+// - DD FET: none (can't do DD on a boost driver)
+#define RAMP_LENGTH 150
+#define USE_DYN_PWM
+
+// level_calc.py 5.01 1 149 7135 1 0.3 1740 --pwm dyn:78:16384:255
+#define PWM1_LEVELS 0,1,1,1,2,3,3,4,5,6,7,8,9,10,11,13,14,16,17,19,21,23,25,27,29,31,34,36,39,42,44,47,50,53,57,60,63,67,70,74,77,81,85,88,92,96,99,103,107,110,113,117,120,123,126,128,130,133,134,136,137,137,137,137,136,135,133,130,126,122,117,111,104,96,87,76,65,52,38,22,23,25,26,27,28,29,30,32,33,34,36,37,39,40,42,43,45,47,49,51,53,55,57,59,61,63,66,68,70,73,76,78,81,84,87,90,93,96,99,103,106,110,113,117,121,125,129,133,137,142,146,151,155,160,165,170,175,181,186,192,197,203,209,215,222,228,234,241,248,255
+#define PWM_TOPS 16383,16383,12404,8140,11462,14700,11041,12947,13795,14111,14124,13946,13641,13248,12791,13418,12808,13057,12385,12428,12358,12209,12000,11746,11459,11147,11158,10793,10708,10576,10173,9998,9800,9585,9527,9278,9023,8901,8634,8486,8216,8053,7881,7615,7440,7261,7009,6832,6656,6422,6196,6031,5819,5615,5419,5190,4973,4803,4571,4386,4179,3955,3745,3549,3340,3145,2940,2729,2513,2312,2109,1903,1697,1491,1286,1070,871,662,459,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255
+#define DEFAULT_LEVEL 50
+#define MAX_1x7135 150
+
+#define HALFSPEED_LEVEL 12
+#define QUARTERSPEED_LEVEL 4
+
+// don't blink halfway up
+#ifdef BLINK_AT_RAMP_MIDDLE
+#undef BLINK_AT_RAMP_MIDDLE
+#endif
+
+#define RAMP_SMOOTH_FLOOR 10  // low levels may be unreliable
+#define RAMP_SMOOTH_CEIL  130
+// 10, 30, [50], 70, 90, 110, 130
+#define RAMP_DISCRETE_FLOOR 10
+#define RAMP_DISCRETE_CEIL  RAMP_SMOOTH_CEIL
+#define RAMP_DISCRETE_STEPS 7
+
+// safe limit ~75% power
+#define SIMPLE_UI_FLOOR RAMP_DISCRETE_FLOOR
+#define SIMPLE_UI_CEIL RAMP_DISCRETE_CEIL
+#define SIMPLE_UI_STEPS 5
+
+// make candle mode wobble more
+#define CANDLE_AMPLITUDE 30
+
+// stop panicking at ~70% power or ~600 lm
+#define THERM_FASTER_LEVEL 130
+#define MIN_THERM_STEPDOWN 80  // must be > end of dynamic PWM range
+
+//#define THERM_RESPONSE_MAGNITUDE 32  // smaller adjustments, this host changes temperature slowly
+//#define THERM_NEXT_WARNING_THRESHOLD 32  // more error tolerance before adjusting
+
+// slow down party strobe; this driver can't pulse for 1ms or less
+#define PARTY_STROBE_ONTIME 4
+
+#define THERM_CAL_OFFSET 5
+
+// the power regulator is a bit slow, so push it harder for a quick response from off
+#define DEFAULT_JUMP_START_LEVEL 21
+#define BLINK_BRIGHTNESS DEFAULT_LEVEL
+#define BLINK_ONCE_TIME 12
+
+// added for convenience
+#define USE_SOFT_FACTORY_RESET