diff options
Diffstat (limited to 'hwdef-Sofirn_LT1S-Pro.h')
| -rw-r--r-- | hwdef-Sofirn_LT1S-Pro.h | 109 |
1 files changed, 80 insertions, 29 deletions
diff --git a/hwdef-Sofirn_LT1S-Pro.h b/hwdef-Sofirn_LT1S-Pro.h index ce6ee3a..c52364f 100644 --- a/hwdef-Sofirn_LT1S-Pro.h +++ b/hwdef-Sofirn_LT1S-Pro.h @@ -1,6 +1,3 @@ -#ifndef HWDEF_SOFIRN_LT1S_PRO_H -#define HWDEF_SOFIRN_LT1S_PRO_H - /* BLF LT1S Pro driver layout using the Attiny1616 Driver pinout: @@ -13,8 +10,10 @@ Driver pinout: */ +#pragma once -#define LAYOUT_DEFINED + +#define HWDEF_C_FILE hwdef-Sofirn_LT1S-Pro.c #ifdef ATTINY #undef ATTINY @@ -22,40 +21,85 @@ Driver pinout: #define ATTINY 1616 #include <avr/io.h> +// channel modes: +// * 0. warm/cool white blend +// * 1. auto 3ch blend (red -> warm -> cool by ramp level) +// * 2. red only +// * 3. red + white blend +#define NUM_CHANNEL_MODES 4 +//#define CHANNEL_MODES_ENABLED 1,1,1,1 +#define CHANNEL_MODES_ENABLED 0b00001111 +#define CM_WHITE 0 +#define CM_AUTO 1 +#define CM_RED 2 +#define CM_WHITE_RED 3 + +// TODO: blend mode should enable this automatically? +#define USE_CHANNEL_MODES +// TODO: blend mode should enable this automatically? +#define USE_CHANNEL_MODE_ARGS +// TODO: or maybe if args are defined, the USE_ should be auto-set? +#define CHANNEL_MODE_ARGS 128,0,0,255 +#define SET_LEVEL_MODES set_level_2ch_blend, \ + set_level_auto_3ch_blend, \ + set_level_1ch, \ + set_level_red_white_blend +// TODO: gradual ticking for thermal regulation +#define GRADUAL_TICK_MODES gradual_tick_2ch_blend, \ + gradual_tick_auto_3ch_blend, \ + gradual_tick_1ch, \ + gradual_tick_red_white_blend +// can use some of the common handlers +#define USE_SET_LEVEL_2CH_BLEND +//#define USE_SET_LEVEL_AUTO_3CH_BLEND +#define USE_SET_LEVEL_1CH +//#define USE_SET_LEVEL_RED_WHITE_BLEND +// TODO: +//#define USE_GRADUAL_TICK_2CH_BLEND +//#define USE_GRADUAL_TICK_AUTO_3CH_BLEND +//#define USE_GRADUAL_TICK_1CH +//#define USE_GRADUAL_TICK_RED_WHITE_BLEND + +#define DEFAULT_CHANNEL_MODE CM_AUTO + +#define FACTORY_RESET_WARN_CHANNEL CM_RED +#define FACTORY_RESET_SUCCESS_CHANNEL CM_WHITE + +#define POLICE_COLOR_STROBE_CH1 CM_RED +#define POLICE_COLOR_STROBE_CH2 CM_WHITE + +// TODO: remove this as soon as it's not needed #define PWM_CHANNELS 1 -#ifndef SWITCH_PIN #define SWITCH_PIN PIN5_bp #define SWITCH_PORT VPORTA.IN #define SWITCH_ISC_REG PORTA.PIN2CTRL #define SWITCH_VECT PORTA_PORT_vect #define SWITCH_INTFLG VPORTA.INTFLAGS -#endif - -// usually PWM1_LVL would be a hardware register, but we need to abstract -// it out to a soft brightness value, in order to handle tint ramping -// (this allows smooth thermal regulation to work, and makes things -// otherwise simpler and easier) -uint8_t PWM1_LVL; // warm tint channel -#ifndef PWM1_PIN -#define PWM1_PIN PB0 // -#define TINT1_LVL TCA0.SINGLE.CMP0 // CMP1 is the output compare register for PB0 -#endif +#define WARM_PWM_PIN PB0 +#define WARM_PWM_LVL TCA0.SINGLE.CMP0 // CMP1 is the output compare register for PB0 // cold tint channel -#ifndef PWM2_PIN -#define PWM2_PIN PB1 // -#define TINT2_LVL TCA0.SINGLE.CMP1 // CMP0 is the output compare register for PB1 -#endif +#define COOL_PWM_PIN PB1 +#define COOL_PWM_LVL TCA0.SINGLE.CMP1 // CMP0 is the output compare register for PB1 // red channel -#ifndef PWM3_PIN -#define PWM3_PIN PB0 // -#define PWM3_LVL TCA0.SINGLE.CMP2 // CMP2 is the output compare register for PB2 -#endif +#define RED_PWM_PIN PB0 // +#define RED_PWM_LVL TCA0.SINGLE.CMP2 // CMP2 is the output compare register for PB2 + +// translate cfg names to FSM names +#define LOW_PWM_LEVELS RED_PWM_LEVELS +#define LOW_PWM_LVL RED_PWM_LVL +#define LOW_PWM_PIN RED_PWM_PIN + +// only using 8-bit on this light +#define PWM_GET PWM_GET8 +#define PWM_DATATYPE uint8_t +#define BLEND_PWM_DATATYPE uint8_t + // average drop across diode on this hardware #ifndef VOLTAGE_FUDGE_FACTOR @@ -64,14 +108,20 @@ uint8_t PWM1_LVL; // lighted button -#ifndef AUXLED_PIN #define AUXLED_PIN PIN5_bp #define AUXLED_PORT PORTB -#endif + +// the button lights up +#define USE_INDICATOR_LED +// the button is visible while main LEDs are on +#define USE_INDICATOR_LED_WHILE_RAMPING + + +// custom channel modes +void set_level_auto_3ch_blend(uint8_t level); +void set_level_red_white_blend(uint8_t level); -// with so many pins, doing this all with #ifdefs gets awkward... -// ... so just hardcode it in each hwdef file instead inline void hwdef_setup() { // set up the system clock to run at 10 MHz instead of the default 3.33 MHz @@ -111,4 +161,5 @@ inline void hwdef_setup() { } -#endif +#define LAYOUT_DEFINED + |