1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
|
/* BLF LT1S Pro driver layout using the Attiny1616
Driver pinout:
* eSwitch: PA5
* Aux LED: PB5
* WW PWM: PB0 (TCA0 WO0)
* CW PWM: PB1 (TCA0 WO1)
* Red PWM: PB2 (TCA0 WO2)
* Voltage: VCC
*/
#pragma once
#define HWDEF_C_FILE hwdef-Sofirn_LT1S-Pro.c
#ifdef ATTINY
#undef ATTINY
#endif
#define ATTINY 1616
#include <avr/io.h>
// channel modes:
// * 0. warm/cool white blend
// * 1. auto 3ch blend (red -> warm -> cool by ramp level)
// * 2. red only
// * 3. red + white blend
#define NUM_CHANNEL_MODES 4
//#define CHANNEL_MODES_ENABLED 1,1,1,1
#define CHANNEL_MODES_ENABLED 0b00001111
#define CM_WHITE 0
#define CM_AUTO 1
#define CM_RED 2
#define CM_WHITE_RED 3
// TODO: blend mode should enable this automatically?
#define USE_CHANNEL_MODES
// TODO: blend mode should enable this automatically?
#define USE_CHANNEL_MODE_ARGS
// TODO: or maybe if args are defined, the USE_ should be auto-set?
#define CHANNEL_MODE_ARGS 128,0,0,255
#define SET_LEVEL_MODES set_level_2ch_blend, \
set_level_auto_3ch_blend, \
set_level_1ch, \
set_level_red_white_blend
// TODO: gradual ticking for thermal regulation
#define GRADUAL_TICK_MODES gradual_tick_2ch_blend, \
gradual_tick_auto_3ch_blend, \
gradual_tick_1ch, \
gradual_tick_red_white_blend
// can use some of the common handlers
#define USE_SET_LEVEL_2CH_BLEND
//#define USE_SET_LEVEL_AUTO_3CH_BLEND
#define USE_SET_LEVEL_1CH
//#define USE_SET_LEVEL_RED_WHITE_BLEND
// TODO:
//#define USE_GRADUAL_TICK_2CH_BLEND
//#define USE_GRADUAL_TICK_AUTO_3CH_BLEND
//#define USE_GRADUAL_TICK_1CH
//#define USE_GRADUAL_TICK_RED_WHITE_BLEND
#define DEFAULT_CHANNEL_MODE CM_AUTO
#define FACTORY_RESET_WARN_CHANNEL CM_RED
#define FACTORY_RESET_SUCCESS_CHANNEL CM_WHITE
#define POLICE_COLOR_STROBE_CH1 CM_RED
#define POLICE_COLOR_STROBE_CH2 CM_WHITE
// TODO: remove this as soon as it's not needed
#define PWM_CHANNELS 1
#define SWITCH_PIN PIN5_bp
#define SWITCH_PORT VPORTA.IN
#define SWITCH_ISC_REG PORTA.PIN2CTRL
#define SWITCH_VECT PORTA_PORT_vect
#define SWITCH_INTFLG VPORTA.INTFLAGS
// warm tint channel
#define WARM_PWM_PIN PB0
#define WARM_PWM_LVL TCA0.SINGLE.CMP0 // CMP1 is the output compare register for PB0
// cold tint channel
#define COOL_PWM_PIN PB1
#define COOL_PWM_LVL TCA0.SINGLE.CMP1 // CMP0 is the output compare register for PB1
// red channel
#define RED_PWM_PIN PB0 //
#define RED_PWM_LVL TCA0.SINGLE.CMP2 // CMP2 is the output compare register for PB2
// translate cfg names to FSM names
#define LOW_PWM_LEVELS RED_PWM_LEVELS
#define LOW_PWM_LVL RED_PWM_LVL
#define LOW_PWM_PIN RED_PWM_PIN
// only using 8-bit on this light
#define PWM_GET PWM_GET8
#define PWM_DATATYPE uint8_t
#define BLEND_PWM_DATATYPE uint8_t
// average drop across diode on this hardware
#ifndef VOLTAGE_FUDGE_FACTOR
#define VOLTAGE_FUDGE_FACTOR 7 // add 0.35V
#endif
// lighted button
#define AUXLED_PIN PIN5_bp
#define AUXLED_PORT PORTB
// the button lights up
#define USE_INDICATOR_LED
// the button is visible while main LEDs are on
#define USE_INDICATOR_LED_WHILE_RAMPING
// custom channel modes
void set_level_auto_3ch_blend(uint8_t level);
void set_level_red_white_blend(uint8_t level);
inline void hwdef_setup() {
// set up the system clock to run at 10 MHz instead of the default 3.33 MHz
_PROTECTED_WRITE( CLKCTRL.MCLKCTRLB, CLKCTRL_PDIV_2X_gc | CLKCTRL_PEN_bm );
//VPORTA.DIR = ...;
VPORTB.DIR = PIN0_bm | PIN1_bm | PIN2_bm | PIN5_bm; // Outputs: Aux LED and PWMs
//VPORTC.DIR = ...;
// enable pullups on the unused pins to reduce power
PORTA.PIN0CTRL = PORT_PULLUPEN_bm;
PORTA.PIN1CTRL = PORT_PULLUPEN_bm;
PORTA.PIN2CTRL = PORT_PULLUPEN_bm;
PORTA.PIN3CTRL = PORT_PULLUPEN_bm;
PORTA.PIN4CTRL = PORT_PULLUPEN_bm;
PORTA.PIN5CTRL = PORT_PULLUPEN_bm | PORT_ISC_BOTHEDGES_gc; // eSwitch
PORTA.PIN6CTRL = PORT_PULLUPEN_bm;
PORTA.PIN7CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN0CTRL = PORT_PULLUPEN_bm; // warm tint channel
//PORTB.PIN1CTRL = PORT_PULLUPEN_bm; // cold tint channel
//PORTB.PIN2CTRL = PORT_PULLUPEN_bm; // red LEDs
PORTB.PIN3CTRL = PORT_PULLUPEN_bm;
PORTB.PIN4CTRL = PORT_PULLUPEN_bm;
//PORTB.PIN5CTRL = PORT_PULLUPEN_bm; // Aux LED
PORTC.PIN0CTRL = PORT_PULLUPEN_bm;
PORTC.PIN1CTRL = PORT_PULLUPEN_bm;
PORTC.PIN2CTRL = PORT_PULLUPEN_bm;
PORTC.PIN3CTRL = PORT_PULLUPEN_bm;
// set up the PWM
// TODO: add references to MCU documentation
TCA0.SINGLE.CTRLB = TCA_SINGLE_CMP0EN_bm | TCA_SINGLE_CMP1EN_bm | TCA_SINGLE_CMP2EN_bm | TCA_SINGLE_WGMODE_DSBOTTOM_gc;
TCA0.SINGLE.PER = 255;
TCA0.SINGLE.CTRLA = TCA_SINGLE_CLKSEL_DIV1_gc | TCA_SINGLE_ENABLE_bm;
}
#define LAYOUT_DEFINED
|
