aboutsummaryrefslogtreecommitdiff
Commit message (Expand)AuthorAgeFilesLines
...
| * | | | went back to continuous lowpass because it had the best noise reductionSelene ToyKeeper2020-02-282-52/+74
| * | | | brute force method for reducing ADC noise -- average a ridiculous number of s...Selene ToyKeeper2020-02-052-20/+14
| * | | | still doesn't work, but at least it's a bit less broken than before...Selene ToyKeeper2020-02-051-8/+12
| * | | | first pass at a smaller simpler thermal regulation algorithm...Selene ToyKeeper2020-02-051-75/+52
| * | | | replaced Anduril's gradual adjustment speed code with a smaller simpler versionSelene ToyKeeper2020-02-051-43/+17
| * | | | saving state of ADC / WDT refactoring before doing more changes... what chan...Selene ToyKeeper2020-01-305-76/+59
| * | | | switched to a pseudo-rolling-average method to reduce noise, set prescaler ba...Selene ToyKeeper2020-01-3010-17/+22
| * | | | increased effective ADC resolution by switching from continuous-lowpass to su...Selene ToyKeeper2020-01-291-64/+43
| * | | | remove truncation noise by adding 0.5 to each resultSelene ToyKeeper2020-01-291-24/+22
| * | | | rewrote ADC code to use a continuous lowpass system on all measurements, to e...Selene ToyKeeper2020-01-2914-139/+203
* | | | | mention the maximum allowed temperature in the manualSelene ToyKeeper2020-02-031-1/+1
|/ / / /
| | | * added FETless KR4 build target, calibrated other KR4 therm faster level betterSelene ToyKeeper2020-03-162-2/+47
| | | * fixed the ADC channel for voltage measurementSelene ToyKeeper2020-03-061-2/+2
| | | * FET ramp was too steep; slowed it down by 50% (20 steps -> 30 steps)Selene ToyKeeper2020-03-061-11/+10
| | | * KR4: added FET channel, measured output, calibrated rampSelene ToyKeeper2020-03-062-5/+13
| | | * initial support for Noctigon KR4Selene ToyKeeper2020-03-054-0/+223
| | |/ | |/|
| | * fixed eeprom corruption after turning boost chip on/offSelene ToyKeeper2020-02-271-0/+16
| | * K1 12V needs party strobe slowed down even moreSelene ToyKeeper2020-02-261-1/+1
| | * added support for boost PMIC enable pin (K1 12V has 2 pins which need to turn...Selene ToyKeeper2020-02-252-2/+12
| | * Added template files for Noctigon K1 12V model.Selene ToyKeeper2020-02-252-0/+206
| |/
| * merged from fsm, mostly to get thermal regulation updatesSelene ToyKeeper2019-12-177-9/+187
| |\ | |/ |/|
* | fixed too-slow thermal response (was introduced in the irq-refactor branch)Selene ToyKeeper2019-12-171-5/+8
* | added support for Fireflies ROT66 G2 and PL47 G2Selene ToyKeeper2019-12-112-0/+109
* | added a compile-time flag to enable/disable momentary mode (suggested by Agro)Selene ToyKeeper2019-12-041-1/+18
* | fixed compile errors to handle a couple USE_ flags better:Selene ToyKeeper2019-12-041-2/+8
* | added a FW3A build with the FET turned off completelySelene ToyKeeper2019-12-031-0/+36
* | adjusted lantern tint ramping power correction again, based on measurements o...Selene ToyKeeper2019-12-031-1/+1
* | adjusted BLF Lantern (Sofirn LT1) tint ramping power correction factor to mat...Selene ToyKeeper2019-11-292-1/+8
| * changed voltage colors to better match Noctigon K1Selene ToyKeeper2019-11-282-5/+5
| * renamed Emisar D1S V2 -> Noctigon K1Selene ToyKeeper2019-11-252-6/+8
| * merged upstream fsm branchSelene ToyKeeper2019-11-2511-31/+73
| |\ | |/ |/|
* | enabled muggle mode again in all build targets, since it fits nowSelene ToyKeeper2019-11-244-23/+0
* | merged d4v2-buttonled branch, which makes the D4V2's lighted button workSelene ToyKeeper2019-11-246-8/+75
|\ \
| * \ merged from upstream fsm branch to get a whole bunch of kernel-level improvem...Selene ToyKeeper2019-11-2421-318/+446
| |\ \ | |/ / |/| |
* | | added -fwhole-program gcc flag, suggested by Agro. Signficantly reduces ROM ...Selene ToyKeeper2019-11-221-1/+1
| * | merged changes from fsm branch, including version check and stuck-button safetySelene ToyKeeper2019-10-1518-58/+596
| |\ \
| * | | slowed down rainbow RGB mode, added a ramp-down on stuck-button for safety pu...Selene ToyKeeper2019-09-071-1/+7
| * | | added button LED support to D4v2Selene ToyKeeper2019-09-066-7/+72
| | | * increased Noctigon K1's default temperature limit to 55 CSelene ToyKeeper2019-11-251-0/+4
| | | * calibrated Noctigon K1, changed voltage divider calibration values to 10-bit ...Selene ToyKeeper2019-11-254-7/+9
| | | * made the button LED turn off in momentary mode, instead of staying on foreverSelene ToyKeeper2019-11-201-2/+7
| | | * merged more updates from fsm / irq-refactor branches, finishing up previous c...Selene ToyKeeper2019-11-209-59/+98
| | | |\ | |_|_|/ |/| | |
* | | | merged tiny fix from irq-refactor branch (fixed spurious wakeup)Selene ToyKeeper2019-11-201-2/+2
|\ \ \ \
| * | | | fixed unintentional wakeup right after going to sleepSelene ToyKeeper2019-11-201-2/+2
* | | | | merged irq-refactor branch, which fixes some small but long-standing issues:Selene ToyKeeper2019-11-1916-310/+399
|\| | | |
| * | | | Mateminco MF01S can fit muggle mode again, barelySelene ToyKeeper2019-11-191-3/+3
| * | | | reduced build size by a few bytesSelene ToyKeeper2019-11-192-3/+3
| * | | | the Q8 can just barely fit muggle mode againSelene ToyKeeper2019-11-191-3/+3
| * | | | enabled prevent_reboot_loop() on all builds, to reduce the impact of any pote...Selene ToyKeeper2019-11-191-5/+7
| * | | | fixed ADC cycles running 2X as fast as intendedSelene ToyKeeper2019-11-191-8/+8
generated by cgit v1.2.3 (git 2.25.1) at 2026-03-28 23:33:43 +0000